Proč je sériový přenos dat rychlejší než paralelní přenos dat?

Obsah:

Video: Proč je sériový přenos dat rychlejší než paralelní přenos dat?

Video: Proč je sériový přenos dat rychlejší než paralelní přenos dat?
Video: 10 Awesome VLC Media Player Tips and Tricks 2024, Březen
Proč je sériový přenos dat rychlejší než paralelní přenos dat?
Proč je sériový přenos dat rychlejší než paralelní přenos dat?
Anonim
Připojení pevného disku SATA je rychlejší než starší připojení pevného disku PATA a to samé lze říci i pro standardy externí kabeláže, ale to je protiintutivní: proč by paralelní přenos nebyl rychlejší?
Připojení pevného disku SATA je rychlejší než starší připojení pevného disku PATA a to samé lze říci i pro standardy externí kabeláže, ale to je protiintutivní: proč by paralelní přenos nebyl rychlejší?

Dnešní zasedání Otázky a odpovědi se k nám přichází s laskavým svolením SuperUser - rozdělení Stack Exchange, komunitní skupiny webových stránek pro otázky a odpovědi.

Otázka

Snímač SuperUser Modest je zvědavý na rychlost přenosu dat u paralelních a sériových připojení:

Intuitively, you would think that parallel data transmission should be faster than serial data transmission; in parallel you are transferring many bits at the same time, whereas in serial you are doing one bit at a time.

So what makes SATA interfaces faster than PATA, PCI-e devices faster than PCI, and serial ports faster than parallel?

I když je snadné se dostat do úvahy, že SATA je novější než PATA, musí existovat konkrétnější mechanismus v práci než věk.

Odpověď

Doprovodník SuperUser Mpy nabízí určitý pohled na povahu typů přenosu:

You cannot formulate it this way.

Serial transmission is slower than parallel transmission given the same signal frequency. With a parallel transmission you can transfer one word per cycle (e.g. 1 byte = 8 bits) but with a serial transmission only a fraction of it (e.g. 1 bit).

The reason modern devices use serial transmission is the following:

  • You cannot increase the signal frequency for a parallel transmission without limit, because, by design, all signals from the transmitter need to arrive at the receiver at the same time. This cannot be guaranteed for high frequencies, as you cannot guarantee that the signal transit time is equal for all signal lines (think of different paths on the mainboard). The higher the frequency, the more tiny differences matter. Hence the receiver has to wait until all signal lines are settled - obviously, waiting lowers the transfer rate.
  • Another good point (from this post) is that one needs to consider crosstalk with parallel signal lines. The higher the frequency, the more pronounced crosstalk gets and with it the higher the probability of a corrupted word and the need to retransmit it. [1]

So, even if you transfer less data per cycle with a serial transmission, you can go to much higher frequencies which results in a higher net transfer rate.

[1] This also explains why UDMA-Cables (Parallel ATA with increased transfer speed) had twice as many wires as pins. Every second wire was grounded to reduce crosstalk.

Scott Chamberlain odráží odpověď Myp a rozšiřuje ekonomiku designu:

The problem is synchronization.

When you send in parallel you must measure all of the lines at the exact same moment, as you go faster the size of the window for that moment gets smaller and smaller, eventually it can get so small that some of the wires may still be stabilizing while others are finished before you ran out of time.

By sending in serial you no longer need to worry about all of the lines stabilizing, just one line. And it is more cost efficient to make one line stabilize 10 times faster than to add 10 lines at the same speed.

Some things like PCI Express do the best of both worlds, they do a parallel set of serial connections (the 16x port on your motherboard has 16 serial connections). By doing that each line does not need to be in perfect sync with the other lines, just as long as the controller at the other end can reorder the “packets” of data as they come in using the correct order.

The How Stuff Works page for PCI-Express does a very good explination in depth on how PCI Express in serial can be faster than PCI or PCI-X in parallel.

TL;DR Version: It is easier to make a single connection go 16 times faster than 8 connections go 2 times faster once you get to very high frequencies.

Musíte něco přidat k vysvětlení? Vypadněte v komentářích. Chcete se dozvědět více odpovědí od ostatních uživatelů technologie Stack Exchange? Podívejte se na celý diskusní příspěvek zde.

Doporučuje: