Jak inteligentní nebo efektivní by mohla být kancelářská síť na pracovišti?

Obsah:

Video: Jak inteligentní nebo efektivní by mohla být kancelářská síť na pracovišti?

Video: Jak inteligentní nebo efektivní by mohla být kancelářská síť na pracovišti?
Video: TOP 15 – Skryté funkce na iPhone (iOS), které musíte znát! 🔥 2024, Březen
Jak inteligentní nebo efektivní by mohla být kancelářská síť na pracovišti?
Jak inteligentní nebo efektivní by mohla být kancelářská síť na pracovišti?
Anonim
Když nastavíte síť v kanceláři a v závislosti na použitém zařízení a nastavení, jak inteligentní a / nebo efektivní by mohla být tato síť skutečně? Dnešní příspěvek SuperUser Q & A má odpověď na otázku zvědavé čtenáře.
Když nastavíte síť v kanceláři a v závislosti na použitém zařízení a nastavení, jak inteligentní a / nebo efektivní by mohla být tato síť skutečně? Dnešní příspěvek SuperUser Q & A má odpověď na otázku zvědavé čtenáře.

Dnešní zasedání Otázky a odpovědi se k nám přichází s laskavým svolením SuperUser - rozdělení Stack Exchange, komunitní skupiny webových stránek pro otázky a odpovědi.

Foto s laskavým svolením felixtriller (Flickr).

Otázka

Čtenář SuperUser bizzehdee chce vědět, jak inteligentní a / nebo efektivní je síť v kanceláři na pracovišti:

There is an argument within my office about how smart/efficient the network we have set up really is. We have a fiber line and a cable line running into a load balancing router, which has a hardware firewall and a 64 port switch connected to it. Each of our workstations are connected to the switch (about 30 machines) plus an NAS and a couple of internal test servers (all assigned 192.168.0.x addresses).

If workstation A wants to communicate with workstation B, is our network smart enough to go:

A → Switch → B and only travel via the first most common connection, or would the path be A → Switch → Firewall → Router → Firewall → Switch → B and have to use that full route every time?

Jak inteligentní a / nebo efektivní může být jejich kancelářská síť na pracovišti?

Odpověď

Uživatelé SuperUser Ben N a Nathan Adams mají pro nás odpověď. První, Ben N:

Routers are not necessary unless your traffic needs to move to a different subnet. When a computer wants to send some IP traffic to a different machine on its subnet, it needs the recipient’s MAC address, since IP addresses are not a thing at the switch level/layer (Layer 2 of the OSI model).

If it does not know the MAC address, it broadcasts an ARP request saying, “Hey, whoever has this IP address, could you tell me your MAC address please?” When the machine gets a response, that address is then attached to the packet, and the switch uses it to send the packet out via the correct physical port.

When the destination is not on the same subnet, routers need to be involved. The sender gives the packet to the appropriate router (usually the default gateway unless you have special routing needs), which sends it through the network to the intended recipient.

Unlike switches, routers know about and have IP addresses, but they also have MAC addresses and that is the MAC address that initially gets put on packets that need routing (MAC addresses never leave the subnet).

You can see router IP addresses in the gateway column of the output of route print on Windows. Destinations that do not require routing have On-link there.

Následuje odpověď od Nathana Adamsa:

If two computers are connected to the same VLAN on a switch and share the same subnet mask, the switch should deliver the packet without hitting your firewall or router.

You can verify this by running tracert 192.168.0.X (assuming you are using Windows) and you should see a direct route to that system.

Musíte něco přidat k vysvětlení? Zní to v komentářích. Chcete se dozvědět více odpovědí od ostatních uživatelů technologie Stack Exchange? Podívejte se na celý diskusní příspěvek zde.

Doporučuje: